Fill Plasterboard

Fill Plasterboard
0 (0)

So that you get a smooth surface, you apply leveling compound evenly after installing the plasterboard. The instructions show you step-by-step how to fill plasterboard: from mixing the filler to pre-filling and finishing up to sanding.

How can I fill plasterboard?

Before you start filling the plasterboard, clean the panels with a hand brush. Then you mix the filler according to the manufacturer’s instructions. As soon as the compound is ready for processing, you start with the pre-filling by filling joints, screw holes and similar unevenness with a spatula. Once the mass has dried, you can level the slabs – if necessary over the entire surface. You can work on transitions to other building materials with silicone or acrylic. Finally, sand down the plasterboard until you get a flat surface.

Rigips or plasterboard panels offer various areas of application in dry construction. With the plasterboard you can, for example, hang ceilings, clad walls, sloping ceilings or ceilings and draw in new walls. Working with panels, stud frames and insulation is comparatively easy, inexpensive and is particularly suitable for designing your own living space.

How to fill plasterboard in 7 steps

  1. Prepare plasterboard for filling
Fill Plasterboard<div class='yasr-stars-title yasr-rater-stars-vv'
                          id='yasr-visitor-votes-readonly-rater-6206483855a66'
                          data-rating='0'
                          data-rater-starsize='16'
                          data-rater-postid='3109' 
                          data-rater-readonly='true'
                          data-readonly-attribute='true'
                          data-cpt='posts'
                      ></div><span class='yasr-stars-title-average'>0 (0)</span>, How To Make Money With Flipping Houses

At a glance

  • Thoroughly sweep off plasterboard with a hand brush
  • Check plates and screws for unevenness
  • If necessary, cut a bevel with a craft knife
  • Use deep ground and crack bridges

That’s how it goes

First, carefully sweep the assembled plasterboard away so that the filler will later adhere well to the substrate. Check again that all drywall screws are countersunk correctly. This is the only way to get an even surface on the plasterboard when filling.

Every plasterboard has a bevel at the factory. This creates a sufficiently wide joint after application in which the filler can hold. You therefore cut a similar bevel with the craft knife where cut panels meet. After removing dust, treat the joints with a deep primer and bandage all joints with a crack bridge.

  1. Mix the filler
Fill Plasterboard<div class='yasr-stars-title yasr-rater-stars-vv'
                          id='yasr-visitor-votes-readonly-rater-66374682a0e86'
                          data-rating='0'
                          data-rater-starsize='16'
                          data-rater-postid='3109' 
                          data-rater-readonly='true'
                          data-readonly-attribute='true'
                          data-cpt='posts'
                      ></div><span class='yasr-stars-title-average'>0 (0)</span>, How To Make Money With Flipping Houses

At a glance

  • Mix leveling compound according to the manufacturer’s instructions
  • If necessary, use ready-made filler

That’s how it goes

Mix the filler in a clean bucket or other container. Let the powder trickle slowly into the cold water. You can find precise instructions in the manufacturer’s instructions. You mix the mixture thicker and dilute it later if necessary. Otherwise, lumps may form in the filler.

Tip: For smaller repairs later, ready-to-use filler from the tube is suitable.

  1. Pre-fill plasterboard
Fill Plasterboard<div class='yasr-stars-title yasr-rater-stars-vv'
                          id='yasr-visitor-votes-readonly-rater-366a429864088'
                          data-rating='0'
                          data-rater-starsize='16'
                          data-rater-postid='3109' 
                          data-rater-readonly='true'
                          data-readonly-attribute='true'
                          data-cpt='posts'
                      ></div><span class='yasr-stars-title-average'>0 (0)</span>, How To Make Money With Flipping Houses

At a glance

  • Apply filler with a trowel or spatula
  • Remove excess material and use it again
  • Then let the mass dry

That’s how it goes

Apply the filler across the joint using a smoothing trowel or spatula and press it in. Then pull off the excess mass with the broad side lengthways to the joint and press it into the next joint. Scrape the smoothing trowel clean every now and then. This works well with a smaller spatula.

Always fill the horizontal joints first, then the vertical ones. If possible, fill vertical joints from bottom to top. This means that the filler is less likely to fall off. Before applying the finishing compound, let the filler dry well.

  1. Fill the screw holes
Fill Plasterboard<div class='yasr-stars-title yasr-rater-stars-vv'
                          id='yasr-visitor-votes-readonly-rater-a618a09463628'
                          data-rating='0'
                          data-rater-starsize='16'
                          data-rater-postid='3109' 
                          data-rater-readonly='true'
                          data-readonly-attribute='true'
                          data-cpt='posts'
                      ></div><span class='yasr-stars-title-average'>0 (0)</span>, How To Make Money With Flipping Houses

At a glance

  • Fill in all screw holes
  • If necessary, countersink the screws deeper and then fill them
  • Then let the filler dry

That’s how it goes

The plasterboard panels are usually screwed together with drywall screws. Sink their heads completely so that you get a flat surface when filling the plasterboard or plasterboard. Check that all screw heads are securely countersunk before filling the screw holes. For a clean surface you need up to three trowels.

But let the filler dry first before you start fine-tuning.

  1. Filling the inside and outside corners of the plasterboard
Fill Plasterboard<div class='yasr-stars-title yasr-rater-stars-vv'
                          id='yasr-visitor-votes-readonly-rater-8ae0a8663426a'
                          data-rating='0'
                          data-rater-starsize='16'
                          data-rater-postid='3109' 
                          data-rater-readonly='true'
                          data-readonly-attribute='true'
                          data-cpt='posts'
                      ></div><span class='yasr-stars-title-average'>0 (0)</span>, How To Make Money With Flipping Houses

At a glance

  • Fill corners and edges
  • Use silicone or acrylic for connections and transitions
  • Secure protruding edges with edge protection profiles

That’s how it goes

If two plasterboard sheets meet in a corner of the room, leave about 5 mm space between the sheets. You fill this joint as usual. For connections and transitions to walls or ceilings made of other materials, use a permanently elastic joint made of paintable silicone or acrylic instead of working with filler. You secure protruding ceiling or wall corners on the outside with an edge protection profile to protect the edges from damage from bumps.

  1. Refill the plasterboard
Fill Plasterboard<div class='yasr-stars-title yasr-rater-stars-vv'
                          id='yasr-visitor-votes-readonly-rater-c04a8326f6826'
                          data-rating='0'
                          data-rater-starsize='16'
                          data-rater-postid='3109' 
                          data-rater-readonly='true'
                          data-readonly-attribute='true'
                          data-cpt='posts'
                      ></div><span class='yasr-stars-title-average'>0 (0)</span>, How To Make Money With Flipping Houses

At a glance

  • Check joints, screw holes and transitions
  • If necessary, touch up defective areas
  • Sand down any unevenness
  • Apply finishing compound
  • Let the masses dry for at least four hours

That’s how it goes

Plasterboard or gypsum plasterboard can usually not be filled in one go. Especially at joints, holes and transitions as well as corners and edges you may have to fill in several times until the surface is even.

Remove unevenness with a spatula or sandpaper and brush the surfaces off again before applying the fine filler. For a particularly flat surface, apply a special finishing compound over a large area when you finish, so that a flat surface is created between the joints, edges and wall or ceiling.

Wait at least four hours before you start fine-tuning the plates.

  1. Sand the plasterboard smooth
Fill Plasterboard<div class='yasr-stars-title yasr-rater-stars-vv'
                          id='yasr-visitor-votes-readonly-rater-048736d616a82'
                          data-rating='0'
                          data-rater-starsize='16'
                          data-rater-postid='3109' 
                          data-rater-readonly='true'
                          data-readonly-attribute='true'
                          data-cpt='posts'
                      ></div><span class='yasr-stars-title-average'>0 (0)</span>, How To Make Money With Flipping Houses

At a glance

  • Finally sand the plate smooth
  • Approach the next ceiling or wall design

That’s how it goes

The last step is to completely sand the plastered plasterboard with a hand sander or a sander. This will remove even the smallest bumps. After filling, you can continue designing the finished wall or ceiling and start painting, wallpapering or tiling.

You need that for your project

Click to rate this post!
[Total: 0 Average: 0]
Also Very Interesting Posts
Make Shabby Chic Furniture Yourself
0 (0)
Shabby Chic

Shabby chic puts vintage furniture in the spotlight. Our guide will show you how you can create the shabby look Read more

Renovating Doors: How To Beautify Interior Doors
0 (0)
Renovating Doors

Worn out, dented by the children's "Bobby Car" or even accidentally damaged when moving in? Using various examples, we will Read more

Renovating The Bathroom: Building The Floor
0 (0)
Renovating The Bathroom

When the walls are tiled, shift work is the order of the day on the floor: It consists of decoupling, Read more

Painting Furniture Properly – Ideas And Tips
0 (0)
Painting Furniture

Whether self-made shelves or tables, wooden garden furniture or vintage furniture from the flea market - lacquers and glazes quickly Read more

Leave a Comment

Your email address will not be published. Required fields are marked *